Out with the old, slowly. We are removing the stacked fridges to get ready for a new residential unit. Unlike others with under-counter boxes, these s...
|
|
|
I'm not sure I'm describing this properly, but my 30' Nomad, in front of the stuffing box, has a support bearing for the prop shaft. That pillow block...
|
|
|
We recently acquired a 1977 27' Marben Trawler with a 70 hp Hercules diesel and Twin Disc MG-502. We ran the boat down from Nanaimo a week ago from wh...
|
|
|
Hi all, a few months back some folks were curious to see how the installation of a DIY mini-split came out, regarding considerations of condenser outd...
|
|
|
I saw a post on Facebook about a two million liability insurance requirement to moor at marinas in Canada. Does anyone else know about this requiremen...
|
|
|
I have never used a diver to clean the bottom of my boat, but we are heading off on a 500 nm trip soon and want the bottom and running gear nice and c...
|
|
|
Yesterday, I noticed, mid-morning, that the ELCI breaker in the laz (where the shore power goes in) had tripped sometime during the night. Completely ...
|
|
|
I am looking for opinions on the best anti-fouling for use in fresh water only. It will be applied in the spring, but I want to buy now before the pri...
|
|
|
2005 Mainship 34T. Single Yanmar 6LYA 375 hp, 1760 hrs. Sidepower bow thruster with upgraded prop. Kohler 8 kW generator, 990 hrs. Original Raymarine ...
|
|
|
Assumable moorage in Ladysmith, BC. This classic West Coast trawler is a gem. It is a perfect liveaboard. There is teak everywhere: decks, caprails, b...
|
|
|
Can anyone tell me what brand shaft seal this is? Note, the metal band on the left is just a hose clamp. [ATTACH type="full" alt="shaft seal.jpg"]1688...
|
|
|
Hi all, would anyone have any information or know anything about the Defever 40 aft cabin flybridge by Sea Stella? I am thinking of purchasing one but...
|
|
|
Furuno MFD12 display. These came out of the inside helm, have never been outdoors and have always been covered. They are in perfect working order and ...
|
|
|
After one year with an ST 30, I decided to move to a 44 as I found a good opportunity and because I love that boat. It's bigger and heavier, so it's m...
|
|
|
Hey all, I'm going to add a cooling system to my ST44 and looking for advice regarding BTU. I do not need to have 20°C in the boat, but just want to f...
|
|
|
I wanted to share these instructions from C-GPT. They worked perfectly for me, and I received the certificate less than a week later. I received two l...
|
|
|
Removed in good working order for a refit. Seaward 11-gallon hot water heater, 120V with engine heat loop. Novakool 9000 refrigerator/freezer. Price i...
|
|
|
I bought a shrink wrapping kit a few years ago to shrink wrap a 28' boat, but then I sold the boat. This kit has only been used once just to test it o...
|
|
|
I’m looking for a surplus or take-out Twin Disc EC300 control station. It can be a single or twin engine station—it doesn’t matter. I just need one fo...
|
|
|
|
To view this email as a web page, click here
To view past issues of this newsletter, click here
Trawler Forum
is owned & operated by Social Knowledge, LLC
2600 E Southlake Blvd
Suite 120-361
Southlake, Texas 76092
Click here to view our privacy policy.
Questions or Comments? Contact support at [email protected].
Add [email protected] to your address book to ensure future emails arrive.
|
|
|
|
|
